What type of dynamic forces may cause indent in plating on forecastle deck and main deck in way of pillars inside forecastle?
Impact pressure forces in way of abrupt or flared bow.
Forces created by waves on the forecastle.
Slamming in way of flat bottom forward of light draught.
Pressure forces caused by green water on deck.
You are on a 10 000 ton chemical tanker that in addition to fixed foam monitors, is equipped with portable foam applicators. One of the applicators is lost. When ordering a new one you would order one with:
A throughput of at least 400 litres a minute and a “throw” of 15 metres?
A throughput of at least 20 litres a minute and a “throw” of 5 metres?
A throughput of at least 250 litres a minute and a “throw” of 12 metres?
A throughput of at least 100 litres a minute and a “throw” of 10 metres?
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
2 times its designed working pressure, but not more than three-fifths of its nominal bursting pressure.
Not less than one and a half times its nominal bursting pressure, but not more than four-fifths of its specified maximum working pressure.
Not more than one and a half times its specified maximum working pressure, but not less than two-fifths of its bursting pressure.
The prescribed test of EPIRB, SART and portable VHF radio set must be entered in:
When a Master takes the leadership in approaching a problem, must his first action be a decision that will directly solve the problem?
Not necessary, he shall use all available resources. He should resist the temptation to step in and do it all by himself.
Yes, take full control. Do not delegate to other officers, to avoid mistake.
No, he should observe the situation, and let the other senior officers solve the situation.
Yes, with his experience, it is most likely that he has the best solution.
How is a Safety Management Certificate obtained?
Ship owner is authorised to carry out internal audits and issue SMC.
Vessel is surveyed by MCA and certificate issued.
Ship owners has Document of Compliance issued, and vessel is assessed and holds all statutory certificates.
RSS issue SMC with Register.
The time indication 121310z means in maritime radio communication:
12th day, 13:10 hours UTC.
12th month, 13:10 hours UTC.
12th day, 13:10 hours local time.
12th month, 13th day, 10:00 hour local time.
Your vessel is involved in a collision with another vessel. What should you as Master tell the Master on the other vessel?
There should be no communication with the other vessel.
Explain your actions prior to the collision and request details of actions taken by the other vessel which resulted in the collision.
Name; Port of registry; Port of destination of your vessel.
Ask if there is any assistance required by the other vessel.
During the survey of Long Range Identification and Tracking (LRIT) equipment, which document must be available to the surveyor to demonstrate compliance with SOLAS?
The Certificate of Compliance with SOLAS V/19-1, bearing the serial number of equipment installation.
A Statement of Installation and Testing by the Application Service Provider in compliance with SOLAS V/26-4.
A report giving the result of the Performance Test, issued by the manufacturer in compliance with the Flag State Authority requirements.
A report giving the result of the Conformance Test issued by an Application Service Provider on behalf of an Administration.
You are close to the entrance to a port in thick fog. You hear the following signal. What does it mean?
That there is a vessel at anchor in the vicinity. She is less than 100 metres in length.
That there is a vessel at anchor in the vicinity. She is more than 100 metres in length.
That there is a vessel aground in the vicinity.
It is the Master’s responsibility to ensure that:
Concerned personnel carry out the onboard training programme effectively.
Life jackets are worn during every training.
All information regarding the onboard training is given to the ship manager.
Safety equipment is not used during the training.
At what calendar interval must lifting appliances on board a vessel be suitably tested by a competent person?
Which word will precede a routine message?
No specific word will precede a routine message.
What is the maximum quantity of cargo permitted to be carried in a single tank on a type II chemical tanker?
The Training Manual shall contain instructions and information on the life-saving appliances and the best method of survival. The training manual shall contain detailed explanations of crew duties in relation to emergency situations. Which of the following tasks or duties shall be included in the manual according to present regulations?
The use of the ship’s line throwing apparatus.
The use of escape routes and other escape methods.
The use of surface to air visual signals to be used by survivors.
The use of navigational equipment for survival crafts.
Noxious Liquid Substances which, if discharged into the sea from tank cleaning or deballasting operations, are deemed to present a hazard to either marine resources or human health or cause harm to amenities or other legitimate uses of the sea and therefore justify a limitation on the quality and quantity of the discharge into the marine environment. Such substances are:
A category “Y” substance as identified in the revised MARPOL Annex II.
A category “X” substance as identified in the revised MARPOL Annex II.
An NLS as defined in ISGOTT revision V.
A liquid cargo that is prohibited for carriage in vessels other than type 1 chemical tanker, as defined in the INC Code.
The steps of the embarkation ladder used must be spaced apart by a distance of:
Equally spaced not less than 300 mm or more than 380 mm.
Equally spaced not less than 200 mm or more than 280 mm.
A cofferdam, a pumproom or an empty tank, located between cargo tanks containing cargoes or cargo residues which might react with each other in a hazardous manner, are all acceptable methods of segregation in chemical tanker stowage according to the IBC Code. For this purpose, it may also be acceptable to have:
A common bulkhead, provided it overlaps for less than 15 % of the length of the bulkhead on the larger tank.
A common bulkhead, provided it is at least 10 mm thick.
An intervening cargo tank containing a mutually compatible cargo or cargo residues.
A cruciform joint, separating two tanks diagonally.
On all UMS operated vessels and also on most other vessels the engine room is equipped with fire detectors. What requirements of testing and checking of the detectors are to be observed?
When testing detectors by suitable equipment (smoke and heat) check that the sensors self controlling system, e. g. a flashing control light etc. is functioning.
Check that the actual detector is giving appropriate signals to the central control unit and that all electric connections are in good order.
Check the detector with heat and/or smoke (in accordance with instructions in its manual).
All the mentioned alternatives.
A tug is connected to the bow of a vessel. Will the force exerted by it be the same at any ahead speed?
No, on the bow the tug uses power to run with the vessel, which reduces the available power on the towline.
No, when the ahead speed of the ship increases the force exerted by the tug will also increase.
Yes, the force would normally be expected to be the same at any speed of the ship.
“…a ship… …intended to transport products with appreciably severe environmental and safety hazards which require significant preventative measures to preclude escape of such cargo. Usually the ship is of double-hull construction, with a variety of tank sizes/capacities”. What is this the definition of?
A type II chemical tanker, as per the IBC Code.
A type I chemical tanker as per IBC Code.
A parcel chemical tanker as per the IACS Construction Regulations.
The “dew point” of a liquid chemical can be defined as:
The temperature at which a saturated gas exhibits condensation.
The temperature at which dry-ice melts in Acetone.
The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is seen at the point when air is saturated with moisture.
The temperature at which a condensable component is saturated with respect to a gas, as in operational terms is seen at the point when moisture no longer detectable in air.
When loading oil in oil tankers, why are you only allowed to load maximum 98 % of the tank capacity?
Due to temperature expansion.
Danger to vessel stability and strength.
What is false regarding the function “Transmission and reception of on scene communications”.
On area A4 this function is based on the use of HF R/T.
On area A1 this function is based on the use of VHF R/T.
On area A3 this function is based on the use of VHF or/and MF R/T.
The use of SART transponder.
As per SOLAS regulations, the general emergency alarm system must be tested:
How would you determine whether a particular cargo transfer hose was compatible with the chemical product to be transferred?
Check the product classification mark stamped on the flange collar of the hose.
Check the colour of the hose against the general classification code in the IBC Code.
Refer to the product entry in the hose manufacturer’s chemical resistance chart.
There will be no need to check. If the hose has been supplied to a chemical tanker, it will have been certified for the transfer of all chemical products.
The mode J2B is used:
For radiotelex-traffic in the MF/HF band between the ship and shore stations.
For telephone traffic in the MF/HF bands between ship and shore stations.
For urgent message transmitting and receiving.
To maintain good relationship among the crew on board a vessel, one must be:
Give authority to others.
Polite and diplomatic while talking to crew members.
Understanding, Co-operative, and have respect from both sides.
Strict and authoritative while giving orders.
What is the maximum quantity of cargo permitted to be carried in a single tank on a type I chemical tanker?
What type of vessel would show the illustrated lights?
A sailing vessel, at anchor.
A sailing vessel, seen from astern, where the edges of her sidelights are both visible.
A sailing vessel less than 20 metres in length, displaying the optional combined lantern in lieu of standard sailing lights, seen head-on.
A sailing vessel of less than 10 metres in length, displaying the mandatory combined lantern inlieu of sailing lights, seen head-on.
Under what convention is the master to ensure that a ship is seaworthy and in a fit state to safely carry a shipper’s cargo?
“Passivation” is a restorative process periodically applied to stainless steel tanks on a chemical tanker. What effect does this process have on the steel surface?
It restores and reforms the passive Chromium Hydroxide surface layer.
It restricts active corrosion on the surface steel.
It restores the surface steel to an even and smooth finish, thereby encouraging drainage during discharge.
The IBC Code prescribes certain design conditions for a cargo heating or cooling system fitted to a chemical tanker. What does it require in respect of pressure within such a system, for any condition other than when it is empty?
That a higher pressure can be maintained within the system than the maximum pressure head that could be exerted by the contents of the cargo tank on that system.
That an automatic alarm is fitted to alert the operator when the pressure within the system drops to within 0,2 bar of the pressure measured at the lowest cargo pressure sensor within the tank.
That the system must be fitted with automatic control valves that will maintain the inlet pressure at not less than 0,2 bar above the return pressure.
Which of the following requirements regarding on board stability data corresponds to present regulations? (NSCL 4/12.1).
Drawings and calculations documenting the stability of the ship, both in intact and all possible damage condition.
A calculation example showing the use of “KG” limitation curves.
A calculation example showing use of “GM” limitation curves.
Stability data produced by stability calculation instruments.
A distress alert has accidentally been sent with the Inmarsat-C installation. One should now:
Make contact with an RCC.
Wait until an RCC reports.
Which personnel must undergo familiarization training on board?
The minimum permissible distance measured horizontally between the ship’s shell plating and the outer side bulkhead of the first cargo compartment on a type II chemical tanker is:
Not less than moulded breadth/15.
Not less than moulded breadth/5.
When on HF band a DSC distress alert is received, you have to listen to:
The radio telephony distress frequency in the band in which the DSC distress alert was received.
8 414,5 kHz (DSC distress frequency in 8 MHz).
The radio-telex distress frequency in the band in which the DSC distress alert was received.
What signal may be given by sound and by light to indicate that a vessel fails to understand the intentions or actions of another vessel, or is in doubt that sufficient action is being taken by the other to avoid collision?
One prolonged blast (flash), followed by five or more short and rapid blasts (flashes).
Five short and rapid blasts (flashes).
Three short and rapid blasts (flashes).
Five prolonged blasts (flashes).
When a character in the NAVTEX message sent is not received in the proper way:
A closely resembling character will be printed.
Any other character will be printed.
The message will not be printed at all until, with repeated transmission, it can be automatically compared and corrected.
Nothing or a special character will be printed.
The relay of a distress-call by an RCC for coast-station begins with:
Regular “updating” of a ships position in an Inmarsat-C installation is necessary:
To have the correct position in case of accidents.
To keep to the correct Inmarsat region.
To enter the correct data to the disk antenna.
To inform the satellite of ships position.
Which VHF channel should be used for intership navigation safety communications?
A SART is used by a vessel in distress. This SART is seen on the screen of a:
Both 3 Cm and 10 Cm radar.
The mandatory color of a hand flare is:
Who are responsible for safe working conditions onboard?
The officer of the watch.
Master, Chief Engineer & Chief Officer.
The carriage of a new Noxious Liquid Substance not yet listed in the IBC Code may be considered possible, provided it is achieved through a “tri-partite” agreement between:
The Flag State of the Shipper/the Flag State of the Charterer/the Flag State of the Receiver.
The IMO/the Port State of the Shipper/the Port State of the Receiver.
The Port State of the Shipper/the Flag State of the Carrier/the Port State of the Receiver.
The Shipper/the Receiver/the Operator or Charterer.
A satellite receives the transmissions of the 406 MHz Cospas-Sarsat EPIRB. The transmissions of the EPIRB will be:
Always passed on to a LUT.
Exclusively passed on to a LUT only between 70° N and 70° S.
Exclusively passed on to a LUT if the satellite sees both the EPIRB and the LUT.
The battery of a SART:
Must be replaced before the expiry date is exceeded.
Must be re-charged weekly.
Charged condition must be checked weekly.
You are on a vessel 10 nautical miles off the coast of Nigeria, West Africa. Are you allowed to dump empty glass bottles overboard?
No, glass bottles can not be dumped overboard.
Yes, glass bottles can be dumped overboard.
Yes, the bottles can be dumped if they are ground so that the resulting particles can pass through a screen with 50 mm openings.
Which of the following is a definition of the “Proper Shipping Name”, as found in the IMDG Code?
The name to be used in any documentation relating to the transportation of the dangerous substance, material or article, such as on forms, labels and placards.
The correct chemical name of a potentially hazardous material, as identified from the Chemical Cargo List.
The name under which a dangerous material, substance or article is described for export purposes in the country of loading.
The name assigned by the manufacturer to a material, substance or article for the purposes of shipment.
Which Convention first placed on the shipowner an obligation to exercise due diligence to make a ship seaworthy, requiring him “before and at the beginning of a voyage … to … make the ship seaworthy … and … make the holds…and all other parts of the vessel in which goods are carried, fit and safe for their reception, carriage and preservation”?
What is the minimum permissible distance measured horizontally between the ship’s shell plating and the outer side bulkhead of the first cargo compartment on a type II chemical tanker?
Not less than moulded breadth/15.
Not less than moulded breadth/5.
With what system is a NAVTEX-message transmitted?
Which one of the given requirements regarding survival craft muster and embarkation arrangements corresponds to the present SOLAS regulations?
Searchlights to be provided at the launching station.
Davit-launched survival craft muster and embarkation stations shall be arranged to enable stretchers to be placed in survival craft.
Muster and embarkation stations shall be readily accessible from accommodation and work areas.
Testing a SART is permitted:
Only at sea, outside territorial waters.
Only in a port or harbour.
At sea, outside territorial waters, and in a port or harbour.
As a result of being in collision with your vessel, the other vessel is involved is on fire. What are your responsibilities?
The other vessel is in distress and if possible I will render assistance.
You should continue on with the voyage if your damage is not serious.
There is no statutory requirement to provide assistance as the actions of that vessel were the primary cause of the collision.
Your vessel should manoeuvre close to the other vessel and aid the fire-fighting operation.
What are the three volumes of the IAMSAR Manual?
A – Command and Control B – Communications C – Rescue Procedures.
I – Planning and Preparation II – Rescue III – Reference.
I – Organization and Management II – Mission Co-ordination III – Mobile Facilities.
I – Organization II – Communications III – Rescue Procedures.
During an audit, adherence to the company cargo handling procedures can best be demonstrated:
By providing a summary of out-turn figures for the auditor.
By requesting that an audit takes place during cargo operations.
By providing a summary of incident and lost time figures for the auditor that reflects a successful and trouble-free system on board.
By being able to provide comprehensive and verifiable documentary records of cargo operations.
What is the probable cause of an error in the position shown on a GPS receiver set into “2D” fixing?
The receiver has defaulted to “3D” fixing and there is no overhead satellite.
Incorrect height of the antenna set into the receiver.
The limit set on the HDOP figure is too great.
The limit set on the VDOP figure is too small.
Master of every ship must provide:
A link between the shipboard training officer and the company training officer ashore.
The training during crews working hours only.
Proper rest to the crew after each training programme.
Facilities to conduct training whenever required by the training officer.
One of the sailors needs urgent medical assistance. The VHF-call starts with:
MARPOL 73/78 defines a “high viscosity substance” as:
A noxious liquid substance in category “X” or “Y” with a viscosity equal to or greater than 50 mPa·s at the unloading temperature.
A noxious liquid substance of any category with a pour point of greater than 37,8 °C.
Any noxious liquid substance, the residues of which cannot be stripped from a cargo compartement and its associated piping and pumping system to equal to or less than 75 litres.
A noxious liquid substance in category “Y” with a viscosity equal to or greater than 100 mPa·s at 37,8 °C.
What immediate action should be taken if a ship unexpectedly runs aground and stops?
Stop engines and tell the engine room to switch over to high suction.
Stop engines and immediately request “Full Astern”.
Sound the General Alarm and plot the ships position.
Which option best completes the following statement? The version of the IHO presentation library on the ECDIS is important because:
It is where the files for maintenance of the system software are stored.
If it is not the latest version, the ECDIS will not be compliant.
It influences the colours on the display.
It allows ECDIS to decide on the scale setting of the chart.
On area A3 the function “Transmission and reception of on scene communications” is mainly based on:
The use of MF and/or VHF R/T.
The use of HF DSC and/or Inmarsat-C.
The use of MF and/or HF R/T.
If drugs are discovered onboard your ship:
Ensure the witness to the discovery signs your incident report.
Write a report a few days after the event and describe everything that occurred.
Disembark crew and passengers as quickly as possible at the next port of call so the authorities can conduct their investigation.
Notify the authorities after you arrive at the next port of call.
A tank which contained a category “X” product must undergo a prewash before leaving port in compliance with MARPOL. The resulting residues shall be discharged to a reception facility until the concentration of the substance in the effluent, as indicated by analysis of samples of the effluent taken by the authorized surveyor reaches a certain level. What is that level?
A cargo pumproom or other enclosed space which contains cargo handling equipment on a chemical tanker shall be fitted with a mechanical ventilation system, capable of being controlled from outside the space. What is the minimum number of atmosphere changes per hour, based on the total volume of the space, that such a system must deliver?
Not less than 10 charges per hour.
Not less than 30 charges per hour.
There is no specified minimum number of changes, provided it is running continuously throughout any cargo operation.
If the ventilation is permanent, it shall deliver at least 20 changes per hour; if it involves part recirculation, then it shall deliver at least 30 changes per hour.
DG placards shall be located on a freight container:
One of the back end and one on one of the sides (only).
One on each end and one on each side.
You are to load a number of chemical cargoes in Rotterdam in December, for eventual discharge in Australia, after the ship has called at Singapore and Malaysia. None of the cargoes on board at any stage of the voyage require heating. None of the tanks to be discharged in Singapore and Malysia will require hot washing after discharge. What will need to be considered when determining the filling limits of the tanks containing the Australian cargoes?
The maximum anticipated temperature that the cargoes will reach bearing in mind ambient air and sea temperatures to be encountered on passage, so that any expansion does not result in overflow.
The accuracy of the tank level monitoring systems in potentially sub-zero conditions.
The anticipated cargo loss due to the projected evaporation rates as the vessel passes through the tropics.
The “dew point” of a liquid chemical can be defined as:
The temperature at which dry-ice melts in Acetone.
The temperature at which a condensable component is saturated with respect to a gas, as in operational terms is seen at the point when moisture no longer detectable in air.
The temperature at which a saturated as exhibits condensation.
The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is seen at the point when air is saturated with moisture.
Which of the following requirements regarding life-buoys correspond to present regulations? (SOLAS III/7.1).
All life-buoys shall be placed in holders with quick-release arrangement.
Not less than half the total number of lifebuoys shall be provided with self-igniting lights.
At least one lifebuoy shall be placed within the vicinity of the stern.
At least one life-buoy on each side of the ship shall be fitted with a buoyant lifeline.
You are carrying a bulk cargo of Phosphoric Acid. Which components of the cargo pumps may be damaged as a result of discharging this particular cargo and why?
The cargo seals may be damaged from the abbrasive effect of any sediment.
The valves in the associated piping may be distorted by pressure surges created by cavitation as the acid is discharged.
The outer casing may be corroded by the unstable impurities within the acid.
The impeller veins may be damaged as a result of the relatively high density of the cargo if the pumps are run at too high a speed.
To what pressure will a new length of cargo hose be tested by a manufacturer prior to its supply to a vessel for service onboard a chemical tanker?
Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its bursting pressure.
2 times its designed working pressure, but not more than three-fifths of its nominal bursting pressure.
Not less than one and a half times its nominal bursting pressure, but not more than four-fifths of its specified maximum working pressure.
Not more than one and a half times its specified maximum working pressure, but not less than two-fifths of its bursting pressure.
What type of Bill of Lading covers “door to door” shipment?
A Through Bill of Lading.
A Destination Bill of Lading.
A Multi-Phase Bill of Lading.
Which of the following two digits codes is used to obtain medical advice?
You are in an area of restricted visibility. You hear this sound signal. What does it mean?
That there is a vessel in distress nearby.
That there is a vessel at anchor in the vicinity.
That there is a vessel aground in the vicinity.
That there is a vessel engaged in underwater operations in the vicinity. She has divers down.
In which of these circumstances can your ship request a DoS?
Your ship is conducting activities with a port or ship that is not required to implement an approved security plan.
There is a heightened security risk for your ship and a port facility.
Your ship is operating at a lower security level than the ship or port it is interfacing with.
Your ship has added a new port to its of ports of call.
Your vessel is approaching a port in restricted visibility and you hear this signal. What kind of vessel is it and what is it doing?
It comes from a vessel engaged in pilotage duties and it is making way through the water.
It comes from a vessel restricted in her ability to manoeuvre.
It comes from a vessel at anchor, less than 100 metres in length.
It comes from a vessel engaged in pilotage duties at anchor, over 100 metres in length.